JLAB PCI TI

TIpcieUS

initial setting after installing card into new machine

It should be 3 scripts in /root directory with following contents:

ti_config:

#!/bin/csh
#
# save TIpcieUS driver config file into /root
#
set temp = `lspci | awk -F' ' '/9038/{print $1}'`
echo $temp
set dest = "/sys/bus/pci/devices/0000:$temp"
echo $dest/config
cp $dest/config /root/config

ti_reload:

#!/bin/csh
#
# TIpcieUS driver reload
#
set temp = `lspci | awk -F' ' '/9038/{print $1}'`
echo $temp
set dest = "/sys/bus/pci/devices/0000:$temp"
echo $dest
cp -f /root/config $dest

ti_menu:

#!/usr/bin/tcsh
#
# William's menu
#
~jgu/PCIeTI/TIpcieUS/tools/TIcontrol /dev/xdma0_user

TIpcieUS

Manual 2024 (pdf)

Old manual 2020 (pdf)

Pinout of the 34-pin connector (TI CPI has 40-pin connector, but first 34 pins are the same, although they are typically NOT ECL but LVDS)

Pin name Signal Name            Signal Level

 1 / 2    BUSY_out              + / - ECL
 3 / 4    Trigger_out           + / - ECL
 5 / 6    UserControlled_out1   + / - ECL
 7 / 8    UserControlled_out2   + / - ECL
 9 / 10   UserControlled_out3   + / - ECL
11 / 12   UserControlled_out4   + / - ECL
13 / 14   OT1                   + / - ECL
15 / 16   PromptTrigger_out     + / - ECL
17 / 18   Inhibit_in            + / - ECL
19 / 20   Trigger_in            + / - ECL
21 / 22   Trigger_ch#1_in       + / - ECL
23 / 24   Trigger_ch#2_in       + / - ECL
25 / 26   Trigger_ch#3_in       + / - ECL
27 / 28   Clock_in              + / - ECL
29 / 30   Trigger_ch#4_in       + / - ECL
31 / 32   Trigger_ch#5_in       + / - ECL
33 / 34   Trigger_ch#6_in       + / - ECL

35 / 36   
37 / 38   
39 / 40   CLK output

Installing driver on newly built machine

ssh boiarino@...

For release 1.4.0 on RHEL7 mchines:

cd /usr/clas12/release/1.4.0/coda/src/TIpcieUS/xdma

For release 2.0.0:

cd /usr/clas12/release/2.0.0/coda/src/TIpcieUS-devel/xdma

make -B

Become superuser (su) and run following:

make install
reboot

NOTE: controlling tool can be used as following:

ssh as root

Run TI control script:

cd ~jgu/PCIeTI/TIpcieUS/tools
./TIcontrol   /dev/xdma0_user

or run following if exists:

/root/ti_init

For slave mode, type '2', then type '9'. It should bring TIpcie board to the right state. After that you can start the daq from scratch.

For Sampa setup, set TI board to the 'bridge' mode by typing '15'.

Another useful option is 4 - it shows temperature etc parameters.

old version

Manual for TI board in PCI format in (pdf)

On some DELL servers (R440 for example) booter will give an pci error and ask to push F1. To disable F1 pushing, in BIOS go to 'System BIOS Settings' -> 'Miscellaneous Settings' -> 'F1/F2 Prompt on Error' and click 'Disabled'.

Sometimes device /dev/TIpcie may be removed during patching or/and rebooting process. To restore it do following as root:

cd $CODA/src/TIpcie/linux_driver
./reload_driver.sh