EPICS HALLB Installation

From CLONWiki
Revision as of 16:14, 30 October 2013 by 129.57.76.91 (talk)
Jump to navigation Jump to search 
///=================================================================================      
///=================================================================================
///========================= SUMMARY BASE AND synApps installation  ================
///=================================================================================
///=================================================================================



 ssh clonioc1/clonpc3

I) BASE INSTALLATION: 

 1) cd $CLAS/R3.14.12.3/
    chown -R sytnik.clas-4 base

 2) edit $CLAS/R3.14.12.3/base/configure/os/CONFIG_SITE.Common.vxWorksCommon

   replace:
   #WIND_BASE = /usr/local/vw/tornado22-$(ARCH_CLASS)
   by:
   WIND_BASE = /apps/VxWorks55/ppc

 3) edit $CLAS/R3.14.12.3/base/configure/CONFIG_SITE

    CROSS_COMPILER_TARGET_ARCHS=vxWorks-ppc604_long

    cd $CLAS/R3.14.12.3/base/
    
    
 4)  edit $CLAS/R3.14.12.3/base/configure/os/CONFIG_SITE.Common.linux-x86

   to uncomment the line: 

  COMMANDLINE_LIBRARY  = READLINE_NCURSES

  (comment out other lines other lines: COMMANDLINE_LIBRARY ) 



 5)
    cd $CLAS/R3.14.12.3/base/
    cp previous_base/include/bigsubRecord.h include/.
    cp previous_base/src/rec/bigsubRecord.c src/rec/.
    cp previous_base/src/rec/bigsubRecord.dbd src/rec/.
    cp previous_base/src/rec/a_out.h src/rec/.



    edit src/rec/Makefile

    to add

    DBDINC += bigsubRecord

    LIBSRCS += bigsubRecord.c    
    
  6) for wiener mpod
  
     edit $CLAS/R3.14.12.3/base/src/dbStatic/dbStaticLib.c
     to replace          char        string[80];
     by        string[256]; 
    
  7)  
    
    make clean uninstall
    make  (to build for linux and VxWorks)  
    
II) synApps installation:

  ssh clonioc1/clonpc3

   http://www.aps.anl.gov/bcda/synApps/
   take and untar synApps_5_5.tar.gz
   cd synApps_5_5/support
   edit suppurt/configure/RELEASE
   
   SUPPORT=$CLAS/R3.14.12.3/synApps/synApps_5_5/support/
   EPICS_BASE=$CLAS/R3.14.12.3/base
   
   edit $CLAS/R3.14.12.3/synApps/synApps_5_5/support/configure/CONFIG_SITE
   
   CROSS_COMPILER_TARGET_ARCHS=vxWorks-ppc604_long

   cd $CLAS/R3.14.12.3/synApps/synApps_5_5/support
   make release
   make (to build linux and VxWorks)
   
 
   
///===============================================================================      
///===============================================================================
///========================= END SUMMARY BASE AND synApps installation  ==========
///===============================================================================
///===============================================================================



//=================================================================================
//=================================================================================
//==========================  MPOD INSTALLATION ===================================
//=================================================================================
//=================================================================================



 ssh clonioc1/clonpc3

edit:

$CLAS/epics/apps/configure/CONFIG_SITE
$CLAS/epics/drivers/configure/CONFIG_SITE



     CROSS_COMPILER_TARGET_ARCHS =

to prevent the building for VxWorks for all 
drivers and applications.
(specific drivers and applications can be configured with their 
CONFIG_SITE separately)

edit:

 $CLAS/epics/apps/configure/RELEASE
 $CLAS/epics/drivers/configure/RELEASE



EPICS_BASE=$(CLAS)/R3.14.12.3/base

cd $CLAS/epics/drivers/snmpApp
make

cd $CLAS/epics/apps/mpodCratesApp
make

launch of the mpod:
cd $CLAS/epics/apps/iocBoot/iocmpodCrates 
./st.cmd  

//=================================================================================
//=================================================================================
//==========================  END MPOD INSTALLATION ===============================
//=================================================================================
//=================================================================================

//=================================================================================
//=================================================================================
//==========================  MOTOR INSTALLATION ==================================
//=================================================================================
//=================================================================================

ssh clonioc1/clonpc3
cd $CLAS/R3.14.12.3/synApps/synApps_5_5/support/xxx-5-5/iocBoot/iocvxWorks

copy there the following files from previous iocBoot/iocvxWorks directory:

claspcal_motor.substitutions
my.cmd
my_alot.cmd 
cdMyCommands

ssh clon10
tsconnect ioctest1
pass: <ret>

<ctrl x> /// to enter into reboot mode 
[VxWorks boot]: p  // command p to print the table balow:
[VxWorks boot]: c  // to change boot configuration (it should be like below)

boot device          : fei
unit number          : 0 
processor number     : 0 
host name            : clon10
file name            : /usr/local/clas/clas12/coda/VXWORKS_ppc/bin/vx5100
inet on ethernet (e) : 129.57.167.84:fffffc00
host inet (h)        : 129.57.167.14
gateway inet (g)     : 129.57.167.99
user (u)             : boiarino
flags (f)            : 0x20 
target name (tn)     : ioctest1
startup script (s)   : /usr/local/clas12/R3.14.12.3/synApps/synApps_5_5/support/xxx-5-5/iocBoot/iocvxWorks/my.cmd



//=================================================================================
//=================================================================================
//==========================  END MOTOR INSTALLATION ==============================
//=================================================================================
//=================================================================================

//=================================================================================
//=================================================================================
//==========================  CAEN HV INSTALLATION ================================
//=================================================================================
//=================================================================================



ssh clonioc1/clonpc3

edit $CLAS/epics/drivers/CAEN_HV/configure/RELEASE:
EPICS_BASE=$(CLAS)/R3.14.12.3/base



edit $CLAS/epics/drivers/CAEN_HV/configure/CONFIG_SITE:
CROSS_COMPILER_TARGET_ARCHS =

to prevent the building for VxWorks for all 
drivers and applications.
(specific drivers and applications can be configured with their 
CONFIG_SITE separately)

cd $CLAS/epics/drivers/CAEN_HV/level0
make // to build old CAEN
make -f Makefile_1 // to build new CAEN



launch of new CAEN:
ssh clonioc1

test mode (from prompt):
 cd0
 mye

to configure and start cron job:
 crontab -e
 
Following - from home directory !!!

to kill ioc and lock semaphore so cronjob will NOT restart it:
 cioc_cron 0

to start ioc and open semaphore so cronjob can continue monitoring; also can be used to restart ioc (without using 'cioc_cron 0'):
 cioc_cron 2



launch of old CAEN:
ssh dcrb1 (e.g.)

test mode:
 cd0o
 myeo

script:
 coioc_cron

crontab -e
0-59/1 * * * *  /bin/csh -c "(source /home/boiarino/.cshrc; coioc_cron 1) > ~/.crontab_ioccaenold1 "

//=================================================================================
//=================================================================================
//==========================  END CAEN HV INSTALLATION ============================
//=================================================================================
//=================================================================================
Retrieved from "https://clonwiki0.jlab.org/wiki/index.php?title=EPICS_HALLB_Installation&oldid=6218"