CycladesTS1000

Cyclades TS1000 Lunux-based Terminal Server, located in Counting Room. Manufacturer's info can be found on Cyclades web site. General information:

  * 16 port console/terminal server
  * IP name: hallb-ts1.
  * default password for super user(root): tslinux
  * web access: user 'root', pass 'tslinux'
  * port numbering: ttyS1-ttyS16 
  * Port connection: 'ssh root:ttySN@hallb-ts1' where N is port number from 1 to 16.
  * Escape sequence to disconnect is "~."

Port Map:

 | *Port#* | *Port name* | *Servername* | *Comment*
 |  1      |   ttyS1     |    hallb-rtr |  BigIron 15000 switch/router
 |  2      |   ttyS2     |    clon00    |  SUN V240 server
 |  3      |   ttyS3     |    clon10    |  SUN E3500 server
 |  4      |   ttyS4     |    clonfs    |  raid system
 |  5      |   ttyS5     |    clonfs2   |  Netapp F87 file server
 |  6      |   ttyS6     |              |  
 |  7      |   ttyS7     |              |  
 |  8      |   ttyS8     |              |  
 |  9      |   ttyS9     |              |  
 |  10     |   ttyS10    |              |
 |  11     |   ttyS11    |              |
 |  12     |   ttyS12    |              | 
 |  13     |   ttyS13    |              |
 |  14     |   ttyS14    |              |
 |  15     |   ttyS15    |              |
 |  16     |   ttyS16    |              |

Cyclades-TS Documentation: Cyclades-TS QuickStart Guide Cyclades-TS User Guide

Initial installation was performed using serial line: IP address, gateway, mask etc.

To connect from console: connect PC to 'console' input and power up.

 login: root
 pass: tslinux

Ports setup was performed from web interface:

 click on 'Serial Ports'
 choose port you want to configure and click 'Submit'
 set 'Authentication Type' to 'Local' ('None' will allowed ssh to port without password)
 set 'Protocol' to 'Socket SSH' (otherwise ssh will not work)
 set 'Server Farm' to the name you want to assign to the port (usually name of device connected to the port, like 'clon10')
 click 'Submit'

Repeat that for all ports you want to setup. When done, click 'Run Configuration', choose 'Serial Ports ..' and click 'Activate Configuration'. Make sure you can connect to all ports you just configured, for example:

 ssh root:clon10@hallb-ts1

To make changes permanent, click 'Load/Save Config' and 'Save to Flash'. Click 'Reboot' and make sure that all ports are working properly.

Wire map:

 RJ45-RJ45->CUS9899(Red)->DB9(f)
 1 (O)   --> 1        
 2 (wO)  --> 2      
 3 (G)   --> 5 --------> 2 
 4 (wBl) --> 6      
 5 (Bl)  --> 3 --------> 5 
 6 (wG)  --> 4 --------> 3 
 7 (Br)  --> 7      
 8 (wBr) --> 8

 RJ45-RJ45->CUS9898(Blue)->DB9(f)
 1 (O)   --> 1        
 2 (wO)  --> 2      
 3 (G)   --> 4 --------> 2 
 4 (wG)  --> 6      
 5 (Bl)  --> 3 --------> 5 
 6 (wBl) --> 5 --------> 3 
 7 (Br)  --> 7      
 8 (wBr) --> 8