CycladesTS1000: Difference between revisions

From CLONWiki
Jump to navigation Jump to search
Boiarino (talk | contribs)
No edit summary
Boiarino (talk | contribs)
No edit summary
Line 2: Line 2:


Cyclades-TS Documentation: [http://clonweb/wiki/clondocs/Cyclades/ts_quickstart_v140_070103.pdf Cyclades-TS QuickStart Guide] [http://clonweb/wiki/clondocs/Cyclades/ts_user_v140_122004.pdf Cyclades-TS User Guide]
Cyclades-TS Documentation: [http://clonweb/wiki/clondocs/Cyclades/ts_quickstart_v140_070103.pdf Cyclades-TS QuickStart Guide] [http://clonweb/wiki/clondocs/Cyclades/ts_user_v140_122004.pdf Cyclades-TS User Guide]
Initial installation was performed using serial line: IP address, gateway, mask etc.


To connect from console: connect PC to 'console' input and power up.
To connect from console: connect PC to 'console' input and power up.
Line 7: Line 9:
   login: root
   login: root
   pass: tslinux
   pass: tslinux
Ports setup was performed from web interface:
  click on 'Serial Ports'
  choose port you want to configure and click 'Submit'
  set 'Authentication Type' to 'Local' ('None' will allowed ssh to port without password)
  set 'Protocol' to 'Socket SSH' (otherwise ssh will not work)
  set 'Server Farm' to the name you want to assign to the port (usually name of device connected to the port, like 'clon10')
  click 'Submit'
Repeat that for all ports you want to setup. When done, click 'Run Configuration', choose 'Serial Ports ..' and click 'Activate Configuration'. Make sure you can connect to all ports you just configured, for example:
  ssh root:clon10@hallb-ts1
To make changes permanent, click 'Load/Save Config' and 'Save to Flash'. Click 'Reboot' and make sure that all ports are working properly.


---++ *Cyclades-TS  1000*
---++ *Cyclades-TS  1000*

Revision as of 11:53, 2 March 2007

Lunux-based Terminal Server, located in Counting Room. Manufacturer's info can be found on Cyclades web site.

Cyclades-TS Documentation: Cyclades-TS QuickStart Guide Cyclades-TS User Guide

Initial installation was performed using serial line: IP address, gateway, mask etc.

To connect from console: connect PC to 'console' input and power up.

 login: root
 pass: tslinux

Ports setup was performed from web interface:

 click on 'Serial Ports'
 choose port you want to configure and click 'Submit'
 set 'Authentication Type' to 'Local' ('None' will allowed ssh to port without password)
 set 'Protocol' to 'Socket SSH' (otherwise ssh will not work)
 set 'Server Farm' to the name you want to assign to the port (usually name of device connected to the port, like 'clon10')
 click 'Submit'

Repeat that for all ports you want to setup. When done, click 'Run Configuration', choose 'Serial Ports ..' and click 'Activate Configuration'. Make sure you can connect to all ports you just configured, for example:

 ssh root:clon10@hallb-ts1

To make changes permanent, click 'Load/Save Config' and 'Save to Flash'. Click 'Reboot' and make sure that all ports are working properly.

---++ *Cyclades-TS 1000*

  * 16 port console/terminal server
  * IP name: hallb-ts1.
  * default password for super user(root): tslinux (actual is the same as for clons)
  * port numbering: ttyS1-ttyS16 
  * Escape sequence to disconnect is "~."
  * Port connection: ssh root:ttySN@hallb-ts1

---++ Port Map

 | *Port#* | *Port name* | *Servername* | *Comment*
 |  1      |   ttyS1     |    bi8k      |  BigIron 8000 switch/router
 |  2      |   ttyS2     |    clon00    |  SUN V240 server
 |  3      |   ttyS3     |    clon10    |  SUN E3500 server
 |  4      |   ttyS4     |    clonfs    |  off-line
 |  5      |   ttyS5     |    clonfs2   |  Netapp F87 filer
 |  6      |   ttyS6     |    bethsw3   |  Cisco Gigabit switch
 |  7      |   ttyS7     |    clas-sc0  |  PC lunux
 |  8      |   ttyS8     |    clonpc3   |  Linux PC server
 |  9      |   ttyS9     |    db5       |  Ingress DB server (HPUX)
 |  10     |   ttyS10    |              |
 |  11     |   ttyS11    |              |
 |  12     |   ttyS12    |              | 
 |  13     |   ttyS13    |              |
 |  14     |   ttyS14    |              |
 |  15     |   ttyS15    |              |
 |  16     |   ttyS16    |              |

---++ Wire map:

  • RJ45-RJ45->CUS9899(Red)->DB9(f)*
 1 (O)   --> 1        
 2 (wO)  --> 2      
 3 (G)   --> 5 --------> 2 
 4 (wBl) --> 6      
 5 (Bl)  --> 3 --------> 5 
 6 (wG)  --> 4 --------> 3 
 7 (Br)  --> 7      
 8 (wBr) --> 8      
  • RJ45-RJ45->CUS9898(Blue)->DB9(f)*
 1 (O)   --> 1        
 2 (wO)  --> 2      
 3 (G)   --> 4 --------> 2 
 4 (wG)  --> 6      
 5 (Bl)  --> 3 --------> 5 
 6 (wBl) --> 5 --------> 3 
 7 (Br)  --> 7      
 8 (wBr) --> 8