January 16, 2019 online meeting minutes - Revision history

Boiarino at 15:57, 16 January 2019

2019-01-16T15:57:08Z

← Older revision		Revision as of 11:57, 16 January 2019
Line 1:		Line 1:
	present: Sergey Boyarinov		present: Sergey Boyarinov, Eugene Pasyuk, vpk, Rafo, Raffaella, Irakli, Ben, Stepan, Cole

	1. Run preparations:		1. Run preparations:

	1. TS scalers readout ~~chnage~~ - Sergey/Nathan: DiagGuiServer reports lifetime and scalers as activemq messages, it is the only place		1. TS scalers readout change - Sergey/Nathan: DiagGuiServer reports lifetime and scalers as activemq messages, it is the only place; Nathan will include changes in epics

	2. add 16-channel scope to FADC - Ben: was implemented by previous meeting, ~~...~~		2. add 16-channel scope to FADC - Ben: was implemented by previous meeting, used in cosmic for few days, no problems so far

	3. add normalized scaler with total charge to FADC250 - Ben: was implemented by previous meeting, ~~...~~		3. add normalized scaler with total charge to FADC250 - Ben: was implemented by previous meeting, same as previous, adcft1/2/3 to be completed

	4. plug RF to right place - Sergey: done		4. plug RF to right place - Sergey: done

			5. Make sure new HTCC trigger is ready - Rafo, Sergey, Ben: Ben will do efficiency study on data and C++code

			6. Trigger dictionary for inbending: new dictionary made by Raffaella with 1GeV threshold and PCALu/v/w; column for HTCC is there and empty; if HTCC dictionary is ready by next wednesday (Jan 23) Ben will implement it for coming run, otherwise we'll leave it for future
	5. ~~Make sure~~ new HTCC ~~trigger~~ is ready ~~- Rafo~~, ~~Sergey, Ben: ...~~

	~~6. Trigger dictionary~~ for ~~inbending: ...~~



	7. Level 3 with helicity correction - Sergey: in progress, coda_l3 is fully implemented, in particular it can be added to configuration using codaedit, started in runcontrol as any other component; helicity delay reporting correction in progress		7. Level 3 with helicity correction - Sergey: in progress, coda_l3 is fully implemented, in particular it can be added to configuration using codaedit, started in runcontrol as any other component; helicity delay reporting correction in progress


	8. New TDs to be installed - Sergey: 2 installed so far, will be done shortly		8. New TDs to be installed - Sergey: 2 installed so far, will be done shortly
Line 32:		Line 27:
	12. BAND need 8 DCS2's and Chris will give them remaining FADCs: all boards installed in both crates: 16 FADCs, 16 DCS2s, 2 v1190 TDCs, all firmwares up to date, coda configuration fixed, ready to go		12. BAND need 8 DCS2's and Chris will give them remaining FADCs: all boards installed in both crates: 16 FADCs, 16 DCS2s, 2 v1190 TDCs, all firmwares up to date, coda configuration fixed, ready to go

			* new cable from sf to piw to get new connector - in progress

			* Chris will cleanup vme filters

			* trigger pattern in ET control word - Sergey will check; for cosmic runs and future data processing

			* implement better roc sync check - coda_mon ??


	2. BONUS readout		2. BONUS readout: waiting for words from Irakli on final solution, if both TPC and MM used we will need 1 new VXS crate - will come from Sacley; 1G should be enough


	3. HPS DAQ/Trigger		3. HPS DAQ/Trigger: all hardware installed, hodoscope+FDCs still in EEL, trigger firmware to go - Ben

Boiarino at 12:42, 16 January 2019

2019-01-16T12:42:54Z

← Older revision		Revision as of 08:42, 16 January 2019
Line 35:		Line 35:


	2.		2. BONUS readout


			3. HPS DAQ/Trigger

Boiarino: Created page with "present: Sergey Boyarinov 1. Run preparations: 1. TS scalers readout chnage - Sergey/Nathan: DiagGuiServer reports lifetime and scalers as activemq messages, it is the only..."

2019-01-16T12:41:46Z

Created page with "present: Sergey Boyarinov 1. Run preparations: 1. TS scalers readout chnage - Sergey/Nathan: DiagGuiServer reports lifetime and scalers as activemq messages, it is the only..."

New page

present: Sergey Boyarinov

1. Run preparations:

1. TS scalers readout chnage - Sergey/Nathan: DiagGuiServer reports lifetime and scalers as activemq messages, it is the only place

2. add 16-channel scope to FADC - Ben: was implemented by previous meeting, ...

3. add normalized scaler with total charge to FADC250 - Ben: was implemented by previous meeting, ...

4. plug RF to right place - Sergey: done

5. Make sure new HTCC trigger is ready - Rafo, Sergey, Ben: ...

6. Trigger dictionary for inbending: ...

7. Level 3 with helicity correction - Sergey: in progress, coda_l3 is fully implemented, in particular it can be added to configuration using codaedit, started in runcontrol as any other component; helicity delay reporting correction in progress

8. New TDs to be installed - Sergey: 2 installed so far, will be done shortly

9. Test setup and spares in counting room - Sergey: ready

10. Check spare pool again, clean up old boards - Sergey, Nathan (RF splitter for example): in progress

11. Install separate crate for v288's (classchv1): done

12. BAND need 8 DCS2's and Chris will give them remaining FADCs: all boards installed in both crates: 16 FADCs, 16 DCS2s, 2 v1190 TDCs, all firmwares up to date, coda configuration fixed, ready to go

2.