December 14, 2011 online meeting minutes - Revision history

129.57.81.115 at 16:12, 14 December 2011

2011-12-14T16:12:43Z

← Older revision		Revision as of 12:12, 14 December 2011
Line 1:		Line 1:
	present: Sergey Boyarinov, ~~Stepan Stepanyan~~, Sandy Philpott, Sergey Bozdnyakov, Eugene Pasyuk, FX		present: Sergey Boyarinov, Nerses, Sandy Philpott, Sergey Bozdnyakov, Eugene Pasyuk, FX

	1. SILO procedure: discussed in details, decided to have 3T scratch buffer on sfs61		1. SILO procedure: discussed in details, decided to have 3T scratch buffer on sfs61
Line 8:		Line 8:

	3.Test setups: HPS trigger cable is too long to get into ADC gate, need to cut off at least 60ns, better 80ns, will reroute trigger cable (probably find faster cable) and Ben will try to make trigger logic faster; rather then that HPS setup seems ready to run with 1881 ADCs; next step will be to replug from 1881 to FADCs and run with new electronics		3.Test setups: HPS trigger cable is too long to get into ADC gate, need to cut off at least 60ns, better 80ns, will reroute trigger cable (probably find faster cable) and Ben will try to make trigger logic faster; rather then that HPS setup seems ready to run with 1881 ADCs; next step will be to replug from 1881 to FADCs and run with new electronics

			We started to assemble Italian setup (called FT prototype)

129.57.81.115 at 16:10, 14 December 2011

2011-12-14T16:10:34Z

← Older revision		Revision as of 12:10, 14 December 2011
Line 7:		Line 7:


	3.Test setups: HPS trigger cable is too long to get into ADC gate, need to cut off at least 60ns, better 80ns, will reroute trigger cable and Ben will try to make trigger logic faster; rather then that HPS setup seems ready to run with 1881 ADCs; next step will be to replug from 1881 to FADCs and run with new electronics		3.Test setups: HPS trigger cable is too long to get into ADC gate, need to cut off at least 60ns, better 80ns, will reroute trigger cable (probably find faster cable) and Ben will try to make trigger logic faster; rather then that HPS setup seems ready to run with 1881 ADCs; next step will be to replug from 1881 to FADCs and run with new electronics

129.57.81.115: Created page with "present: Sergey Boyarinov, Stepan Stepanyan, Sandy Philpott, Sergey Bozdnyakov, Eugene Pasyuk, FX 1. SILO procedure: discussed in details, decided to have 3T scratch buffer on s..."

2011-12-14T15:52:11Z

Created page with "present: Sergey Boyarinov, Stepan Stepanyan, Sandy Philpott, Sergey Bozdnyakov, Eugene Pasyuk, FX 1. SILO procedure: discussed in details, decided to have 3T scratch buffer on s..."

New page

present: Sergey Boyarinov, Stepan Stepanyan, Sandy Philpott, Sergey Bozdnyakov, Eugene Pasyuk, FX

1. SILO procedure: discussed in details, decided to have 3T scratch buffer on sfs61

2. g14b: logbook fails quite often now (almost daily), have to do something; switched to 2-sector trigger without L2, 1.5kHz event rate, 93% livetime, will be main trigger for the rest of the run; HV TOF mf#10 was repaired (one board was bad); 1881 was replaced in TOF, will check it in test setup

3.Test setups: HPS trigger cable is too long to get into ADC gate, need to cut off at least 60ns, better 80ns, will reroute trigger cable and Ben will try to make trigger logic faster; rather then that HPS setup seems ready to run with 1881 ADCs; next step will be to replug from 1881 to FADCs and run with new electronics